DotPod Max, where the Dotmod range stands now

The name has stayed put while the catalogue has not. Under the DotPod Max badge, Dotmod now sells a V1, a V1.5, a clear-shelled Max Lite, an engraved edition called Link, a rebuildable deck and a long run of decorated series. Anyone simply after the brand’s 60 W pod kit has to look past near identical photos to find the real differences, and British listings add a regulatory layer of their own. Here is what the manufacturer’s pages actually say.

DotPod Max in short, the state of the range

The DotPod Max is now less a single device than a platform. Every version shares the base Dotmod describes, with a 60 W ceiling, a side-filled cartridge, a single button, draw activation, adjustable airflow and USB-C charging.

Only one technical step separates the generations. The V1.5 moves to a 2100 mAh battery against 2000 mAh on the V1, and swaps the original small screen for a 0.87 inch colour display. The Max Lite carries that battery and screen in a clear polycarbonate body, while the Max Link is simply an engraved V1.5.

Everything else in the catalogue is finish, whether illustrated series, laser engraving or colourways. For a buyer, the decision that matters is the cartridge type and the coil resistance rather than the model name.

From the original DotPod Max to the V1.5

Both generations still sit side by side on Dotmod’s French shop. The V1 is listed with its 2000 mAh battery and the V1.5 with 2100 mAh, a gain of 5 per cent, for the same maximum output.

The visible difference is the display. British retailers that set out both models give the same figures, with the screen growing from 0.69 to 0.87 inches and turning colour, plus three interface themes named Core, Volt and Mech.

Neither the cartridges nor the coils change. Original pods and coils carry straight over, spares are sold under a single name with no generation attached, and both boxes list the same parts.

Measured against the grid we apply to any new e-cigarette sold as an upgrade, the V1.5 is a revision. The coil platform and the format are untouched, and only the battery and the screen move forward.

Max Lite and Max Link, two variants that are easy to confuse

Both names appear side by side in the catalogue, with the same 2100 mAh battery and the same 60 W ceiling. Their logic runs in opposite directions, since one strips the kit back while the other dresses up the V1.5.

The Max Lite, a clear shell and a smaller box

The Max Lite swaps aluminium for a transparent polycarbonate chassis, edged with RGB lighting that the manufacturer offers in 8 modes. It keeps the colour screen and works with both cartridge types in the range.

The most practical difference sits in the box list. Dotmod names the device, one pod and the manual, with no replaceable-coil tank, no dotCoils and no cable mentioned. The Lite therefore makes most sense for someone who already owns the range’s consumables, and British shops list it alongside the V1.5.

The Max Link, an engraved V1.5

The Link copies the V1.5 specification line for line, large colour screen included. What sets it apart is deep engraving cut into the body, offered in silver, gunmetal and gold. Its box is the V1.5 box, tank and dotCoils included, and in use nothing separates it from a standard V1.5.

What every version shares

Whatever the badge, the shared base stays intact, and the airflow control moves the draw from tight to more open without a change of cartridge.

That stability has a practical benefit that rarely gets mentioned. Consumables bought for a V1 work on a V1.5, a Lite or a Link, so a new reference never forces a change of cartridges. Vaporesso takes the same approach with the Luxe Q pod family, whose pods cross over between devices.

Two cartridges and two coil families

This is the point product pages bury deepest. The range runs on two distinct cartridges, each with its own resistance values, much as the choice of pod shapes the delivery on larger battery pod mods such as the Armour G.

The integrated coil pod carries a mesh coil that cannot be removed. Dotmod sells it in pairs at 0.4, 0.6 or 1.0 ohm, presenting 1.0 ohm as the tightest draw, and British retailers list the same three values. When the coil is spent, the whole pod is replaced.

The empty tank takes interchangeable dotCoils instead. The manufacturer pairs it with three values, 0.3, 0.7 and 0.9 ohm, none of which overlaps the integrated pod, so moving from one system to the other changes the delivery as well as the upkeep.

A third option exists for builders. The DotPod Max RBA is a rebuildable deck with airflow set by 8 interchangeable pins from 0.8 to 3.4 mm, and it was showing as out of stock on the brand’s French shop when we checked.

The standard V1 and V1.5 box contains both systems, an integrated pod and a tank supplied with two dotCoils. That lets you compare the two deliveries before settling on one.

What British rules change on a DotPod Max

The manufacturer’s pages quote 5 ml cartridges and a 4 ml RBA. In Britain those figures cannot describe a compliant nicotine setup, because the rules cap a nicotine-containing tank or pod at 2 ml, refill bottles at 10 ml and nicotine strength at 20 mg per ml.

In practice, read the capacity printed on the British box rather than the figure on a global spec sheet. Any larger number belongs to another market or to nicotine-free use.

Nicotine vaping products are not for sale to anyone under 18 in the UK. HMRC’s Vaping Products Duty applies from 1 October 2026, with duty stamps required on vaping products outside duty suspension from 1 April 2027, so British packaging is set to change again even where the hardware does not.

Special editions and what reaches British shelves

Of the 28 references in the DotPod Max category of Dotmod’s French shop, more than three quarters are editions. Engraved, illustrated, forged carbon and lettered versions mostly sit on a V1.5 base and keep its specification.

Several are customised in France according to their product pages, among them the laser engraved GT and Onna and the illustrated Hunter, and the Lite now has its own sub-category of 7 custom models.

The British retailers we checked list eight colourways instead, one of them a patterned Damas finish that a British guide describes as a finish rather than a separate device. None of these editions changes how the kit is used.

What to watch on the DotPod Max next

No release calendar appears on Dotmod’s French shop. Three signals are worth following all the same.

The first is the V1. While it stays listed, checking the battery capacity and the colour screen in the product title avoids mixing up the generations.

The second is consumables. The RBA returning to stock and continued availability of all three pod values would show whether the brand keeps supporting the whole platform or concentrates on the Lite.

One signal remains, and it is technical. A future generation will only deserve the name if it changes the cartridge or the coils, rather than only the battery or the screen as the V1.5 did.

FAQ

The questions that come up most often about the range concern upkeep and cartridge compatibility.

How do you fill a DotPod Max cartridge?

Through a port on the side of the cartridge, according to the manufacturer, whether you use the integrated pod or the dotCoil tank. After filling or fitting a new coil, letting the wick soak for a few minutes before the first draw lowers the risk of a burnt taste.

Which resistance gives the tightest draw?

The 1.0 ohm integrated pod is the one Dotmod links to its tightest draw, used with the airflow nearly closed. The low values, 0.4 ohm in a pod or 0.3 ohm as a dotCoil, aim at a more open draw and more vapour.

Do you have to press the button to vape?

No, draw activation is enough. The single button mainly handles settings and navigation on the screen.

Can an integrated coil pod be refilled several times?

Yes, for as long as the coil stays healthy. Fading flavour or a burnt taste mean the whole pod needs replacing, since the coil cannot be removed on that format.

Do these cartridges fit other Dotmod devices?

No. The manufacturer presents its replacement pods and its RBA as compatible with this range only. Before buying a cartridge, check that its exact product name refers to the DotPod Max.

DotPod Max, a platform best read through its cartridges

Behind the growing list of references, the range has seen one technical step, the V1.5, and one change of structure, the Max Lite. Everything else dresses a base that has not moved, which protects the consumables you already own.

To follow the DotPod Max without getting lost, look at the cartridge, the coil value and the capacity on the British box before the edition name. It is also the most useful grid for reading the next pod announcements, whichever brand is making them.

Editorial content for adult readers only. Nicotine is highly addictive. Nicotine vaping products are not for sale to anyone under 18 in the UK. This article is not a buying recommendation.